Ce-doped Zn-Al layered double hydroxide(LDH) nanocontainer was synthesized by a co-precipitation method. X-ray diffraction(XRD), Fourier transform infrared spectroscopy(FT-IR), scanning electron microscopy(SEM) and transmission electron microscopy(TEM) methods were used for the characterization of the LDH nanocontainer. The anticorrosion activity of the LDH powders embedded in a hybrid sol-gel coating on aluminum alloy 2024 was investigated by electrochemical impendence spectroscopy(EIS). The results showed that Ce(III) ions were successfully incorporated into LDHs layers. The sol-gel coating modified with Ce-doped Zn-Al LDHs exhibited higher anticorrosion behavior compared with both unmodified and Ce-undoped LDHs containing coatings, which proved the applicability of Ce-doped LDHs in delaying coating degradation and their potential application as nanocontainers of corrosion inhibitors in self-healing coatings.
The effect of temperature on the corrosion behavior of 3003 aluminum alloy in ethylene glycol–water solution was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) techniques. The surface characterization was observed and determined by scanning electron microscopy(SEM), atomic force microscopy(AFM) and energy dispersive spectrometer(EDS). The results demonstrate that the anodic aluminum dissolution and the cathodic oxygen reduction were accelerated by the increased temperature. However, as temperature was over60 °C, the solubility and concentration of oxygen decreased, resulting in the inhibition of cathodic reaction. The cathodic reaction rate of 3003 aluminum alloy rose to the maximum at 60 °C. The Warburg impedance in Nyquist diagram diminished and then was replaced by a negative capacitance caused by the absorption of intermediate corrosion product on electrode. On the other hand,after potentiodynamic measurements, 3003 aluminum alloy suffered pitting corrosion. The dissolution of aluminum alloy around secondary phase particles expanded both horizontally and vertically.
制备了以十二烷基硫酸钠(SDS)为模板的介孔碳,并将介孔碳和单质硫采用熔融渗透法复合制得硫/介孔碳复合材料。SEM、TEM和BET结果显示介孔碳成直径约为500 nm的大小均一的球体,存在孔径为2 nm的微孔;单质硫充分填充在介孔碳的微孔中。以硫/介孔碳复合物作为锂硫电池正极材料时显示出高的电化学性能。初始放电容量高达1 519 m Ah·g-1,在200 m A·g-1的电流密度下充放电200个循环后依然能保持在835 m Ah·g-1。硫/介孔碳复合材料的高倍率性能和优异的循环稳定性,源于介孔碳良好的导电性及其孔结构的固硫作用。
Graphene-reinforced 7055 aluminum alloy composites with different contents of graphene were prepared by spark plasma sintering(SPS). The structure and mechanical properties of the composites were investigated. Testing results show that the hardness, compressive strength, and yield strength of the composites are improved with the addition of 1wt% graphene. A clean, strong interface is formed between the metal matrix and graphene via metallurgical bonding on atomic scale. Harmful aluminum carbide(Al_4C_3) is not formed during SPS processing. Further addition of graphene(above 1wt%) results in the deterioration in mechanical properties of the composites. The agglomeration of graphene plates is exacerbated with increasing graphene content, which is the main reason for this deterioration.
Anodized composite films containing Si C nanoparticles were synthesized on Ti6Al4 V alloy by anodic oxidation procedure in C4O6H4Na2 electrolyte. Scanning electron microscopy(SEM), energy dispersive spectroscopy(EDS) and X-ray photoelectron spectroscopy(XPS) were employed to characterize the morphology and composition of the films fabricated in the electrolytes with and without addition of Si C nanoparticles. Results show that Si C particles can be successfully incorporated into the oxide film during the anodizing process and preferentially concentrate within internal cavities and micro-cracks. The ball-on-disk sliding tests indicate that Si C-containing oxide films register much lower wear rate than the oxide films without Si C under dry sliding condition. Si C particles are likely to melt and then are oxidized by frictional heat during sliding tests. Potentiodynamic polarization behavior reveals that the anodized alloy with Si C nanoparticles results in a reduction in passive current density to about 1.54×10-8 A/cm2, which is more than two times lower than that of the Ti O2 film(3.73×10-8 A/cm2). The synthesized composite film has good anti-wear and anti-corrosion properties and the growth mechanism of nanocomposite film is also discussed.
The effect of sodium tartrate concentrations on morphology and characteristics of anodic oxide film on titanium alloy was investigated. The alloy substrates were anodized in different concentration solutions of sodium tartrate with the addition of PTFE emulsion and their morphology and characteristics were analyzed. The anodic oxide film presented a uniform petaloid drums and micro-cracks morphology. Additionally, micro-cracks dramatically swelled with the increase of the tartrate concentrations. The thickness of the anodic oxide film increased with the concentrations until the concentration reached 15 g/L. The results of Raman analysis illustrate that all samples have similarity in the crystal structure, consisting of mainly amorphous TiO_2, some anatase TiO_2 and a small amount of rutile TiO_2. And the ratios of anatase TiO_2 and rutile TiO_2 increase with the concentrations until it reaches 15 g/L. Furthermore, the intensity of the peaks increases with enhanced concentrations until the concentration reaches 15 g/L. The corrosion resistance of the anodic oxide film is increased by the sodium tartrate with higher concentrations before15 g/L. The coefficient of friction of the anodic oxide film reduces with the concentrations until the concentration reaches 15 g/L, then the coefficient of friction of the anodic oxide film increases with the concentrations.
Ma KunYu MeiLiu JianhuaLi SongmeiWu LiangYao Wenhui